Silent Performace:

• PC-V1000Z separated the system into two zones, allow batter air flow for better silent performance.
  

• PC-V1000Z equipped two large size fans to improve the silent issue, there is a 120mm fan in the front  and a 120mm fan  at the rear, featured low RPM with high air flow to get the best balance between silent and cooling. There is a three-speed fan controller, factory setting to middle (1240RPM), user can adjust it to suit.
  

• To reduce the noise, Lian Li designer fitted the anti-vibration rubber rings on the fan holder to absorb the vibration which cause the noise.
   
  
• There are anti-vibration rubber pad fitted in the chassis to stop the vibration which cause the noise.

Creative Thermal Solutions:

• PC-V series chassis has two heat zones, one zone for motherboard, graphics card and optical drives, and one zone for 3.5” HDD and power supply unit. To separate the heat sources for better thermal solution.
  
  
• Lian Li fitted a 120mm intake fan on PC-V1000Z, The fan can output high air flow volume  with lower RPM to push the cold air through the HDD rack. It can be adjust by the three-speed fan controller, factory setting to meddle (1240RPM), user can adjust the fan speed to suit.
  .
  
• The case front fitted with vented 5.25” bezels, allow the cold air to enter the chassis, there are air filter on the bezel to stop dust entering the chassis!
  
  

• There is a 120mm exhaust fan at the rear to draw the hot air out, and improve the air flow inside the chassis. It can be controlled by the three-speed fan controller, factory setting to Middle ( 1240RPM), user can adjust to suit.
  
  

• PC-V1000Z Features a three-speed fan controller, user can adjust the fan speed to get the best balance between  silent and cooling. Factory setting to Mid Speed (12cm:1240RPM; 14cm:980RPM), user can adjust the fan speed to suit. (12cm:1020~1240~1500RPM; 14cm:800~980~1180RPM)
  
  
• Where air enter the chassis, there is a need for an air filter to hold the dust.

  PC-V1000Z fitted a washable air filter, it can easy remove from the fan unit, no tool required, and it is recyclable.
  
  

• PC-V1000Z equipped a vented PCI bracket, it can improve the cooling issue at the lower part of the motherboard.
  
  

• Today’s motherboards using heat pipe solution to solve the heating problem, therefore the all new V series change the motherboard back to up-right position, and there are opening on he motherboard tray allow to air to cool the rear of the motherboard.
  
  

• PC-V1000Z Features a 140mm fan next to the graphics card to cool the graphics cards and north bridge chip set. It can be connected to the three-speed fan controller, factory setting to Middle (980RPM), user can adjust the fan speed to suit.
  
  

• Power supply unit located at the lower part of the chassis, and it can get the cool air from the bottom of the chassis. Ideal for keep power supply in lower temperature to keep in best output performance, also keep the components cold to extend the life cycle.

• There are two openings on the rear of the top cover, for user who want to use liquid cooling system in PC-V1000Z. There are also two dust-free cover to cover up the openings.

User Frinedly:

• Solid side panel can be released by pulling out a latch, no tool required! User can easy access the case.
  
  

• PC-V1000Z features S-ATA hot sawp HDD cage, simple install the aluminum rail to the HDD, and slide the HDD into the case on the runner, and it is simple to use, and support Raid. 
  
  

• Secure the HDD in the running is very simple, just press down the stop which located at both side of the runner to hold the HDD in position.

   
• Front intake Fan with Air Filter mounted with thumb screws, by release the thumb screws, user can remove the fan unit, easy for service the fan or clean up the air- filter.
  
  
• PC-V1000Z has room to hold 180mm long power supply units. The power supply mounted on a mounting holder, simply slide out the power supply for service.
  
  

• Lian Li Designer putting some effect to protect user’s hardware. There is a lock at the rear of the case for lock the side panel to stop people to access the chassis.
  
  

• There is a set of wheels at the base of the chassis, for user to move the case around, it is made of high quality aluminum alloy. Lian Li designer also put in a lock to hold the wheel in position.
  
  

• The multi-media I/O ports has upgraded onPC-V1000Z! Now the I/O ports located on the top of the case for easy access. Due to today's requirement, Lian Li designer add extra USB ports, and provide new interface, now PC-V1000Z has total four USB 2.0 ports, and E-SATA connectors. There are also a dust -free cover to protect the I/O ports.
  
  

• PC-V1000Z equipped a transparent side panel, for user to monitor hardware condition without opening the side panel.