Lian Li TYR PCX2000 (PC-X2000F-B, PC-X2000FB, PC-X2000-FB) All Aluminum Full Tower Computer PC Case

Lian Li TYR PCX2000 (PC-X2000F-B) All Aluminum Full Tower Computer PC Case- BLACK, with USB 3.0 Ports

TYR PC-X2000F has two-heat zones design to have better thermal solution and tidy up internal space.
The new internal layout has the motherboard on middle level, which allows for easier access to the motherboard as well as more room above, thus larger CPU coolers can be used. To install the power supply unit, just slide the power supply unit throguh the opening at the rear of the case.

Silent Performace:

The fans are mounted with Lian Li’s anti-vibration fan mounting system; the rubber ring grommet absorbs the vibration, keeping the case silent.
The aluminum PCI tool-less mounting module is equipped with a rubber pad which can hold the graphics card firmly while closing the gap found in the PCI bracket and PCI slot to reduce noise from escaping air and furthermore reduce vibrations.
TYR PC-X2000F features Lian Li SAS hot swap HDD cage, which allow user to fit seven of 3.5 HDDs. It is easy to use, no tool required, there are aluminum handles for HDDs, allow user to install or remove HDD easier.
The power supply has rubber pads for both insulation and support. The mounting clip is also aligned with rubber to reduce vibrations but also and also secure the PSU without scratching the painted surface.

Creative Thermal Solutions:

TYR PC-X2000F features two-heat zone design,�upper zone holds four opticals and four HDDs. the lower zone holds the motherboard, power supply unit and three HDDs. to separate the heat sources for better thermal solution.
there are three of 140mm fans at the front to bring the cold air into the system. The fans cover the whole motherboard, and they can remove the heat fast.
In the upper zone, there is a 140mm exhaust fan at the rear to draw the hot air out, and improve the air flow inside the chassis.
In the lower zone, there is a 140mm exhaust fan at the rear to draw the hot air out, and improve the air flow inside the chassis.
There is a openings on the motheboard tray to allow user removed the CPU cooler.
There are vents on the PCI slots, provids extra cooling to graphics card.

.
The power supply unit is at the bottom of the case. It can draw in cold air directly through the vent below the power supply unit. This cooler, fresh air will keep your PSU components more cool and stable and thus extend the PSU lifecycle.
TYR PC-X2000F supports liquid cooling system, the two holes at the rear of the case allows water tubes to pass through, and the rubber cover can protect the tubes away from cutting.
On the back of case has fitted a fan controller, user can adjust the fan speed to get the best balance between silent and cooling.

User Frinedly:

Multi-media port connectors follow international specification standards, with one connector for easy installation. New USB3.0 ports x 4, e-SATA, Audio supports HD Audio. The dual design is for better compatibility options. All I/O ports on the top cover, allow for easy access, there is also a dust-free cover to protect these connectors.
There is a PCI Bracket allow user to connect USB3.0 cable from I/O port to Motherboard.
There is a modular 5.25 optical drive cage, simple un-do the thumb screw, and silde the 5.25 optical drive cage out, mount the 5.25 optical drive.
To install PCI add-on cards require no tools at all. Simply open the aluminum arm of the tool-less PCI add-on card holder, insert the add-on card to the motherboard slots, and close the aluminum arm to hold the add-on card in position. The additional rubber padding on the aluminum arm assists in gripping the card bracket and securing it firmly.
To release the solid side panel, simple just un-do the thrumb screw, and pull the latch. There is a hook for security lock.
There are openings on the panel between different layers, Lian Li has fitted a protection kit to avoid sharp edge damage user's hand or cut the wires.
To install PSU require no tools. Simply open the aluminum PSU holder, insert the PSU in position, also can turn PSU's fans up or down to suit your need, then close the aluminum PSU holder.

There is an air filter at the base of the case to stop dust from entering the case. The filter is washable. The vents are specially designed to retard heat and fire crossover should a short circuit cause sparks and excessive heat within your system. This feature is designed to prevent the problem from spreading outside your case should the unlikely event occur with your components.

Where air enter the chassis, there is a need for an air filter to hold the dust. There is�a washable air filter in the front, it can easy remove, no tool required, and it is washable.
Aluminum M/B Thumb Screw, user can easily screwed motherboard without tools.